This thread's discussion is locked. If it doesn't give you the information you need, head to its forum board for active discussions or to start a new discussion.
Hey all, really weird one here. I've talked to Tech Support, the guy who installed the boxes, and no one can figure it out. It's a Sharp TV, 1080p, good enough for my mother-in-law, and when I go on the website, there's no codes for the TV model, so I get 12 to try, 1 works.
Small detail here, I know, but might mean something. During programming, you enter the code, light beside the TV button flashes. Press the TV button, then the OK button. When you press the OK button, the light beside the TV button is supposed to flash, but the light beside the Optik button comes on instead.
Anyways, I finish programming, and the TV function is so erratic, it's useless.
Now this is for my cognitively impaired MIL, change is not good.
Only 12 codes? There are more than that available for Sharp:
1179 1402 1746 1376 1301 1927
1669 1656 1639 1375 1182 1180
1932 1779 1747 1720 1638 1530
1517 1290 1212 1181 1178 1152
Also when programming, do you press and hold the TV button until the TV turns off, before hitting OK?
There is also:
Power sync your digital box and TV
I was referring to the 12 codes given on the website. I got the codes you listed from an email from my installer.
As for button combo, yes, I press OK after I press the TV button.
And I always power sync when I do a test.
Thank-you for your insights though, good to know I'm on the right track.
As long as you press OK after the TV shuts off, that should work.
If you haven't already, I'd try every code listed for Sharp. Depending on the age of the TV, one of those should work. Some may only allow certain functions like to turn it on, but not off.
Nope. A few of the codes, 4 or 5 would erratically shut the TV off and on, just like the blanket one 1179, I can't get the TV lights to flash when I press okay, only the Optik light comes on. Something wrong with the remote?
Okay, so I swapped remotes, and now the lights flash in the right place, but the result is the same. Once I program 0007 into the remote to powercycle both the box and TV at the same time, the box goes off, not the TV. Press again, TV goes off, box comes on, etc, etc. So, I turned the box on, when the TV was on and the box was initially off, same result. Box goes off, TV does not. Does anyone have any ideas, I'm fresh out.
Once programmed, the Optik button turns on, once, both items. Then, you never know what you'll get with regards the TV. The TV button does exactly what it's supposed to, turn on and off on command. And, before you ask, when the TV is on, and the box off, have I manually turned the box on to sync them? Yes, and when I do that, just the box turns off, again. It's as if the "box off" command overrides everything else that's on. I even tried switching boxes, to no avail. I may have to run a cable over there, since it seems to work on the other 2 Tv's.
To clarify.... the behavior is....
If the TV stays on, press the TV button to turn the TV off.
Pressing the green button again would turn the Optik and TV on again to repeat the cycle.
Some other thoughts to turning the TV off....
Yes, what you're suggesting does work, but I have to take into account my dymentia-plagued mother-in-law. I can't ask her to remember that sequence. I sometimes have to go and turn one or the other on, as she's hit the wrong button.
As for room type, it doesn't matter, bright or dark, and I'm sitting 6ft from the TV when doing all these tests.
Maybe the PikTV interface would be easier for her. Live channels only; limited selection of channels, and a single on/off button.