rf94z's profile

Organizer

 • 

9 Messages

Closed

Regular Internet outages when using bypassing Telus router

Just wanted to get something on the forum that might be a benefit to others running into the situation I've run into with a number of Telus business and home clients. The problem occurs when you want to bypass the ActionTec router that Telus provides and use your own. The ActionTec can either be in bridge mode or removed from the circuit completely and firewall/router duties replaced by your own on-premises device. In our case, all the affected circuits had the ActionTec replaced by Sonicwall firewalls. The main symptom is that the connection appears to drop periodically and no traffic is received by your on-premises firewall from the Telus gateway. Monitoring the connection showed that the connection would go down every 37 minutes precisely from the time it was reset (a simple unplug of the Internet cable usually did the trick). If left on its own, the connection would resume 2 hours and 53 minutes later, and the cycle would continue. Telus support was of no help at all, unsurprisingly, but analyzing packet captures revealed unusual ARP (Address Resolution Protocol) behavior. Sonicwall support confirmed that the problem was a "non-standard implementation of ARP". When I contacted Telus, they eventually confirmed that ARP was disabled on the circuit and is disabled on every circuit that the ActionTec T3200H router is deployed on. After Telus enabled ARP on the circuit, the connection stabilized completely. ARP is an essential last hop protocol and should never be disabled but, for some reason, Telus chooses to disable it. Consequently, it causes drop-out problems in moderately more sophisticated home and business environments that need more functionality than the simple ActionTec modem provides. Note that Telus will enable ARP on a business service but will not on a residential service, so in that case you're stuck with the ActionTec modem. Normally this is not a problem, but if you need more sophisticated services such as a VPN, you're simply out of luck. The only solution for a home user is to upgrade your circuit to business and have Telus enable ARP. I suppose you could downgrade to residential without losing the ARP setting but haven't tried. Hope this saves someone from the hours of work I had to do to figure it out. Telus was of very little help, sadly but unsurprisingly.

This conversation is no longer open for comments or replies and is no longer visible to community members.

Friendly Neighbour

 • 

5 Messages

Hey!

I’m having the same issues with the dropped connections. I just switched to Telus Business 1GB Fiber and the intermittent drops are driving me insane. To give you some background I’m using my own router (Ubiquiti Edge Router ER-4) to bypass the Telus router completely, this is for security and performance reasons. I’m plugged directly into the SFP port. Anyways, I followed your suggestion after spending hours explaining my issues to tech support, at first they had no clue what ARP was. They went ahead and enabled it (at least that’s what they tell me, I don't have much faith so far) and I’m still having issues!! Any suggestions other than to use the Telus router in bridge mode, because I will not use their hardware. Please let me know if you want to see my config files, I’m happy to post them if that will be useful.

Organizer

 • 

9 Messages

If using the ActionTec router in bridge mode works for you, I'd recommend you just go with it. The router is really just a dumb layer 2 device in that configuration. What sort of pattern are you seeing with dropouts? How long is the connection up before it drops? Have you run a packet capture on the circuit?

Friendly Neighbour

 • 

5 Messages

As I mentioned I can’t use it for security reasons. The connection is usually up for about two hours then drops for about 1-2 minutes. I’ll run one now, should I be looking for something in particular. It’s fine if your not sure, I’m just not able to use the Telus router.

Organizer

 • 

9 Messages

Look for a conversation between the Telus gateway and your device that might indicate a lack of response from one side or the other just before an outage. Not sure why you think there is a security issue with the ActionTec in bridge mode but if it's non-negotiable, just replace the ActionTec modem with your own small smart or dumb gigabit switch. I've seen an intermediate switch solve drop out issues on Telus circuits.

Neighbour

 • 

1 Message

Props to you, rf94z, and to Paul Reid for taking the time to post this issue.

 

I had the exact same 37:00 up, 2:53:36 down problem with our Sonicwall router on a new fibre install.  Thanks to the information you guys posted I was able to point the Telus tech to the "enable the ARP port" solution and get it resolved quickly.  Fortunately a tier 2 tech answered the call had some past experience with similar issues - really cut down on the time spent finger pointing before we got down to having it fixed by tier 3.

 

One thing I'll add is that enabling the ARP port didn't immediately fix the connection and get me ping response.  They also had to power cycle the Nokia modem.

 

 

 

 

Neighbour

 • 

1 Message

Thank you for this detailed post and thread. I am a residential fibre customer and have been suffering these disconnects for a couple of years now and finally was able to find a resolution once you pointed me towards the ARP issue.

 

The Sonicwall TZ400 has some "undocumented" options which include allowing for some less than secure behaviours. I enabled Open ARP Behaviour on the TZ400 that allows it to respond to ARP requests from 0.0.0.0 Depending on your use case this may or may not be a good idea. It's entirely possible that I do not fully understand the security implications of doing this either.

 

Further, I asked them for their Actiontec device but instead of putting it in bridge mode I just put it away and deployed its MAC address on the TZ-400 WAN interface. It's been over a week of a stable Fibre connection in over two years.

 

I did try using the Actiontec in bridge mode but it wasn't enough and I had to still configure the Sonicwall TZ400 to respond to ARP requests from 0.0.0.0 So I figured if that was the root cause then there was no need for this extra device. So I am back to SFP->Nokia ONT->TZ400->LAN etc

 

Top Contributors

View More

Community Stats

Loading...

Total Posts

Loading...

Total Members

Loading...

Total Posts with Accepted Solutions

Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...