04-07-2018 03:22 PM - edited 04-07-2018 03:28 PM
I have placed my T3200 fibre modem into bridged mode...
It works fine for about an hour and then goes offline,, requiring a reboot to get my connection back...
any ideas ???
I have factory reset the mode many times,,, currently it is factory mode, with wifi disabled and in bridged mode...
Solved! Go to Solution.
04-08-2018 04:21 PM - edited 04-08-2018 04:21 PM
Are you on DSL or FTTP?
If the latter you can use a switch between the ONT and the Actiontec and your Sonicwall and that should avoid any Actiontec related issues.
04-07-2018 04:11 PM
Do any of the suggestions in this thread help?
04-07-2018 04:17 PM
have not tried the last step....
but the previous entries were all about power saving feature...
my bridged modem is plugged into a Sonicwall NSA2400 firewall that has no power saving features..
04-07-2018 05:03 PM
So, what happens to the Sonicwall NSA2400 if you remove power from the T3200M?
04-07-2018 05:31 PM
nothing,,,, still no internet,,,
only a power cycle on the t3200m restores the connection
04-07-2018 05:52 PM
So......., try the last step in the link posted earlier.
Bridging does not bypass the T3200M, it only causes it to pass traffic without processing it.
04-07-2018 06:08 PM
fingers crossed,,, did factory reset and the double power cycle,,
disabled wireless,,
disabled ipv6
enabled port bridging..
04-07-2018 07:30 PM
04-07-2018 08:19 PM
There may be clues in the actiontec log.
Also you may have to enable wifi on the actiontec so that you can look at lan port status before and after the failure. Also the port status post failure may be a clue, if cycling up down or just down.
Same problem on different ports or cables
04-08-2018 04:10 AM - edited 04-08-2018 04:18 AM
Outta curiosity, did the "T3200M wonkines" start when you put it in Bridge Mode??
I had a T3200M for quite a few months with no issues ... decided to put 'er in Bridge so I could do some IoT stuff. Worked fine for a few weeks, then within the last week, the T3200M would reboot it self up to a 10 times in 24hr period. Called up Telus, they couldn't see any logs on the device, so they sent out a technician. Tech said they've been having issues with the devices and the software ... (and somehow replacing with same model & firmware would solve it) ... I left the new devices in default mode and it worked fine for first 12 hrs. Figured "sweet, all clear" ... put it into Bridge Mode and worked fine for next 12 hrs .. then <bam> ... have had 3 restarts in 4 hours.
I've switched Port Bridging off as I have a sneaking suspicion that Telus just straight up doesn't play nice with it at all.
Numerous times on phone calls they say they don't support it and don't recommend it, usually with excuse that "it's confusing for people and it's troublesome" ... maybe to lay-person who doesn't understand proper networking
Unfortunately, because can't pull logs off the devices as it's all locked down, there's no way to verify it isn't Telus mucking with something as a means to discover bridging.
I'm doing a test trial to see how many self-restarts happen with port bridging off, but unless someone at Telus can prove (ex: via logs) that they are not sabotaging something (accidental or otherwise), then I'm gonna guess it's actually Telus who doesn't understand networking and that's why they don't want others turning on bridging.
I'm seeing reports from others where bridging "magically start working" then all of a sudden in last week the modem keeps self-restarting ...
What's up Telus?
04-08-2018 01:46 PM - edited 04-08-2018 01:46 PM
just discovered this in my Sonicwall log,,,
not sure if it's the T3200 or the sonicwall causing it
when this happens I loose WAN connection and need to release,renew..
151 04/08/2018 10:01:21.256 Warning Firewall Event Wan IP Changed 209.121.12.203, 0, X1
152 04/08/2018 10:01:21.256 Info DHCP Client DHCP Client got ACK from server. 209.121.12.1, 67, X1 209.121.12.203, 68 209.121.12.203
153 04/08/2018 10:01:17.944 Info DHCP Client Sending DHCP REQUEST. 0.0.0.0, 68, X1 255.255.255.255, 67 209.121.12.203
154 04/08/2018 10:01:17.944 Info DHCP Client Got DHCP OFFER. Selecting. 209.121.12.1, 67 209.121.12.203, 68 209.121.12.203
155 04/08/2018 10:01:17.928 Info DHCP Client Sending DHCP DISCOVER. 0.0.0.0, 68, X1 255.255.255.255, 67
156 04/08/2018 10:01:17.928 Warning Firewall Event WAN DHCPC IP Changed
157 04/08/2018 10:01:16.816 Info DHCP Client Sending DHCP RELEASE. 209.121.15.178, 68 10.27.191.182, 67 209.121.15.178
04-08-2018 01:53 PM
Is the "release/renew" on the T3200M or your bridged modem as well?
I have a Nighthawk X4S and when the T3200M hiccups, it eventually reconnects after approx 4 min ... then my Nighthawk has to reconnect as well, so another ~3-4 min .... sometimes up to 10 min.
I'm curious if given enough time (~15min?) both your devices will recover on their own, or the _only_ way is to reboot?
04-08-2018 02:12 PM
this log is from the NSA2400 firewall,,,
it looses connection after 20-50 minutes...
It has reconnected itself twice after 6-9 hours...
but a release/renew on the WAN interface connected to the T3200 fixes issue..
04-08-2018 02:20 PM
duh,, never mind,,, those release renew commands are from me... 😞
so,, the 2400 and the t3200 looses connectivity for some reason ???
I did connect a notebook straight to the T3200 and it seems to maintain connection..??
04-08-2018 02:24 PM
one thing I did noticed is that the WAN ip addresses that it's grabbing are all over the board
209.121.15.*
75.157.71.*
04-08-2018 03:09 PM
going to put it out of bridged mode...
would port forwarding all ports to the firewall essentially duplicated bridged mode ???
if yes... would there be any performance hit ?
04-08-2018 03:53 PM
conclusion --
when the WAN ip address changes on a Sonicwall NSA2400 it requires either a reboot or WAN ip release/renew..
When I take the T3200 out of bridged mode and hook it up to my Sonicwall,, the WAN ip on the sonicwall gets a 192.168.1.* address...
Just in case I added a reservation for the Sonicwall on the T3200.
It has been stable for the past couple of hours...
Conclusion : in Bridged mode the T3200 seems to be getting a new WAN ip, which casuses disconnect on the NSA2400..
going to try to put the NSA2400 in the DMZ of the T3200 ,,, or port forwarding the entire range to it.
04-08-2018 04:21 PM - edited 04-08-2018 04:21 PM
Are you on DSL or FTTP?
If the latter you can use a switch between the ONT and the Actiontec and your Sonicwall and that should avoid any Actiontec related issues.
04-08-2018 06:55 PM
wow it worked !!!!!...
that idea never came to me !!,, makes sense !!!
going to try and bypass the T3200 and run the optik tv straight off the sonicwall..
04-08-2018 07:14 PM
crap optik tv box needs to hooked up tothe t3200 for some reason...
On the sonicwall it works for about 5 seconds...than goes dark
hunting for a small gigabit switch now 🙂
04-09-2018 01:24 AM
Need compatible router (supports IGMP+MultiCast, I believe).
So you're saying the bridge mode looks to be the cause? I'm starting to believe the same on mine, not impressed with Telus on this 😞